AutoEnginuity Domestic ScanTool Bundle (SP05) is an excellent choice for independant shops, tuners & the Do it Yourself mechanic needing access to Ford, GM & Chrysler's OBDII systems for help diagnosing problematic vehicles.

Ford

Using the enhanced Ford interface, a typical Ford vehicle will support 200 - 300 sensors within half a dozen systems; that's essential systems such as ABS, airbags, GEM, ICM, etc. AutoEnginuity's enhanced Ford interface coverage is only matched by factory tools; we have support for 4,800+ sensors selected from 94 systems. Support includes ISO, SCP, CAN, MCAN, and CAN 14229 controllers. The Ford enhanced interface has support for Ford of Europe diesel models such as Ka, Mondo, Galaxy, Fairlane, etc. Finally, our Ford enhanced has support for non-CAN and CAN 400+ bi-directional commands and dozens of system-level tests. With bi-directional controls, you will no longer be relegated to being just an observer in the operation of the vehicle--now you can take control of its operation.

GM

Our enhanced GM interface supports 6,400+ sensors selected from the engine, transmission, body, and chassis systems. For you tuners out there, our enhanced GM interface gives you access to the Crank Variation Learned test for most vehicles. Also, with our enhanced GM coverage is support for Workhorse 04+ MY vehicles (P42 Series, W22 Series, W24 Series, W52 Series, LF72 Series, P32 Series, W18 Series, FE20 Series, W42 Series). Our enhanced GM interface coverage is only matched by factory tools; we have support for 6,000+ sensors selected from all 68 systems. Finally, our enhanced GM has support for 2,000+ bi-directional commands and key system-level tests. With bi-directional controls, you will no longer be relegated to being just an observer in the operation of the vehicle--now you can take control of its operation. Support includes dual-wire and single-wire CAN powertrain support.

Chrysler

Our enhanced Chrysler interface supports hundreds of sensors selected from the powertrain, body, chassis, and transmission system. It includes hi- and low-speed sensor support giving you more sensors and faster throughput then our competitors. This enhanced interface comes with its own hardware interface specifically designed for Chrysler SCI and CCD based controllers. By doing a stand-alone interface we can offer you more SCI coverage then our competitors who are limited by electrical issues with generic OBD-II. Also supported is the CR2 and CR3 Sprinter ('04 - '06), Jeep Liberty Diesel ('05 - '06), diesel Cummins engines, and the Venom equipped Vipers ('08+).

The Domestic ScanTool Bundle #SP05 Includes:

• ProLine Interface (ST06)
• Enhanced Ford Expansion (EI01)
• Enhanced GM Interface (EI02)
• Enhanced Chrysler Expansion (EI04)

What AutoEnginuity's Scan Tool can do:

• Save, print, read and clear Stored and Pending P, U, B, and C Trouble Codes. Supporting P0 - P9 generic and manufacturer specific codes (including the new lettered codes (e.g., P06A0)
• The largest manufacturer specific trouble code library of all PC/PDA-based scan tools (30,000+)
• Read and clear Freeze Frame data
• View live vehicle sensors in a meter, graph, or grid format
• View oxygen sensor live data and test results
• View all 11 Inspection/Maintenance systems and Mode 6 data
• Unlimited logging of live vehicle sensors in TXT, XML, or CSV (1ms logging accuracy)
• Playback your data logs for offline analysis
• Run and query specific component and system tests. Support for generic and enhanced bi-directional tests
• View generic and manufacturer enhanced data on the same tool
• English or Metric (SI) units of measure supported
• Configure your sensors' ranges, scaling value, audible alert triggers, units, and sampling rate
• Savable configurations. Set up the interface to suit your preferences and save it so you never have to do it again
• Supports 1996 and newer passenger vehicles, whether it be domestic, Asian, or European.
• SAE interfaces: J1850 (PWM and VPM), ISO-9141-2, ISO-14230 [KWP2000], and CAN [11bit and 29bit]

System Tests: Ford (EI01)

• PATS Timed Key Programming ('96 - '08)
• KOEO
• KOER
• Power Balance (CAN-based models)
• EVAP Bay Test
• Service Bleed (Non-CAN support not available with ProLine currently)
• Buzz Injector
• Cylinder Contribution Test
• Switch Test
• Glow Plug Test
• System Self-Test
• Low - and High Speed Fan
• All Outputs On/Off
• Injector Coding (1.8L and 2.0L)
• KAM Reset
• Tire Size Programming up to 40" ('99-'03 7.3L, and '04-'07 6.0L trucks)
• IVD Initialization
• Steering Angle / Yaw Rate / Acceleration Sensor Reset ('03 Explorer and Lincoln LS)
• Passenger Seat ReZero
• Power Seat Calibration Test
• Audio Network Communication Test
• Vehicle In-Motion IO Test
• Front Wiper Self-Test
• Rear Wiper Self-Test
• Diesel Particulant Filter Reset, Clear EGR Adaptive Tables, and Clear Fuel Injector Adaptive Table

System Tests: GM (EI02)

• ABS Automated Bleed Routine (ProLine Connector)
• Crank Variation Learn (See: GM-specific vehicle systems for engines support details.)
• Injector Flow Rate Programming (CAN Based Diesels)
• TDC Learn

System Tests - SBEC/JTEC: Chrysler (EI04)

• EGR System Test
• EVAP System Monitor Service Test
• Erase All DTC Fault Codes
• Generate Full Field Test
• Gov & 3-4 Shift Valve Test - JTEC Only
• Leak Detect Pump Test
• Purge Vapors Test
• Reset All Adaptive Memory Fuel Cells
• Reset All Non-Volatile Memory
• Reset CAM/Crank Misalignment
• Reset CAM, Crank, and Sync Status Record
• Reset Duty Cycle Monitor
• Reset Engine Running Time Record
• Reset Fuel Shut-off Record
• Reset Intake Airflow Control Stepper Motor Position
• Reset Trip Information
• Set Sync Signal - JTEC Only
• Set Minimum Throttle Position to Maximum
• Torque Converter Clutch Test - JTEC Only

VPW Based System Tests:

• ABS Bleed Brakes (EBC325, Mk20e, and Mk25e)
• Tire Size Programming
• Transmission Rear/Front Wheel Brake Torque Test
• Transmission Pump Test
• Transmission Quick Learn
• Transmission TCC Break-In Test
• Transmission Front Wheel Pinion Factor

NGC System Tests:

• Injector Kill Test
• NVLD Force Monitor Test
• Purge Vapor Tests
• Reset all On-Board Control Units
• Report Part Number
• Report Reflash Program Counter

CAN Based System Tests:

• ABS Brake Bleed
• Cylinder Performance Test
• EATX Quick Learn
• IMA Injector Programming
• Injector Quantity Adjustment
• LDP Forced Monitor Test
• OCM Verification Test
• Tire Size Programming

Coverage on Demand:

It's a powerful concept pioneered by AutoEnginuity that allows you to purchase enhanced options as you need them. Since enhanced interfaces are software-based updates for our ScanTool line that, once purchased, can be activated through email. There is no extra installation or special hardware necessary. The enhanced interfaces come with free updates for the first 12 month period. There is no annual license fee and you can transfer your license to another PC if necessary. For another 12 months of updates, the cost is $100.00 USD. You are not required to purchase updates and can continue to operate the existing enhanced version for as long as you'd like. We release an average of 4 updates per 12 month period.

Below are some example screen shots of AutoEnginuity while connected to a 2006 F250 Powerstroke.